EIGRP Routing With Redistribution

EIGRP (Enhanced Interface Gateway Routing Protocol)

For same Autonomous no. -->

Redistribution with different Autonomous No.

    1.   It is used for 2 different autonomous system

    2.   Redistribution depend of 5 component

   1.Bandwith

   2.Dely

   3.Load

   4.Reliablity

   5.MTU (Max. transmission unit)

     Basic Configuration And Clock Rate

First router(2621-XM) and add port(WIC-2T) and Follow this Diagram

Go to first router in cli mode and type

          No

          Router>en

          Router#conf t

          Router(config)#int s0/0

          Router(config-if)#ip address 192.168.30.1 255.255.255.0

          Router(config-if)#no shut

          Router(config-if)#clock rate 64000

          Router(config-if)#exit

          Router(config)#int f0/0
   Router(config-if)#ip address 192.168.10.1 255.255.255.0
   Router(config-if)#no shut

          Router(config-if)#exit

Go to second router in cli mode

          No

          Router>en

          Router#conf t

          Router(config)#int s0/0

          Router(config-if)#ip address 192.168.30.2 255.255.255.0

          Router(config-if)#no shut

          Router(config-if)#exit

          Router(config)#int s0/1

          Router(config-if)#ip address 192.168.40.1 255.255.255.0

          Router(config-if)#no shut

          Router(config-if)#clock rate 64000

          Router(config-if)#exit

          Router(config)#int f0/0

          Router(config-if)#ip address 192.168.20.1 255.255.255.0

          Router(config-if)#no shut

          Router(config-if)#exit

Go to Third router in cli mode

          No

    Router>en

          Router#conf t 

          Router(config)#int s0/0

  Router(config-if)#ip address 192.168.40.2 255.255.255.0

          Router(config-if)#no shut

          Router(config-if)#exit

          Router(config)#int f0/0

          Router(config-if)#ip address 192.168.50.1 255.255.255.0

          Router(config-if)#no shut

          Router(config-if)#exit

Step 2 Routing  

In First Router

First check network in (Router# Show ip route)

Then type

Router#conf t

Router(config)#router eigrp 10

Router(config-router)#network 192.168.10.0

Router(config-router)#network 192.168.30.0

In Second router

Router# Show ip route

Router#conf t

Router(config)#router eigrp 10

Router(config-router)#network 192.168.20.0

Router(config-router)#network 192.168.30.0

Router(config)#router eigrp 20

Router(config-router)#network 192.168.40.0

Router(config-router)#network 192.168.20.0

In Third router

Router# Show ip route

Router#conf t

Router(config)#router eigrp 20

Router(config-router)#network 192.168.40.0

Router(config-router)#network 192.168.50.0

Step 3 Redistribution

Go to that router in which two or more autonomous no. are present (router 2) 
and redistribute 
for example
In these condition go to router 2 and follow the step's

Go to first AS

Router(config)#Router eigrp 10

Router(config-router)#Redistribute eigrp 20 metric 1544 2000 255 1 1500

Router(config-router)#Exit

Go to Second AS

Router(config)#Router eigrp 20

Router(config-router)#Redistribute eigrp 10 metric 1544 2000 255 1 1500

Where:-

1544          -        Bandwith

2000          -        Dely

255            -        load

1                 -        Reliability

1500          -        MTU

To check Send Packet's Between Networks or ping from fist router to all ip's as shown in picture