IPV6-EIGRP ROUTING

-

IPV6-EIGRP ROUTING

in ipv4 routing 

Diagram 
Router 2811 and switch 2950T 


Basic Configuration,clock rate and bandwidth 

Go to First Router
Router>en
Router#conf t
Router(config)#int s0/0/0

Router(config-if)#ipv6 address 2002::1/64
Router(config-if)#no shut
Router(config-if)#clock  rate 64000
Router(config-if)#bandwidth 1000
Router(config-if)#exit

Router(config)#int f0/0
Router(config-if)#ipv6 address 2001::1/64
Router(config-if)#no shut

Go to second Router 
Router>en
Router#conf t
Router(config)#int s0/0/0

Router(config-if)#ipv6 address 2002::2/64
Router(config-if)#no shut
Router(config-if)#bandwidth 1000
Router(config-if)#exit

Router(config)#int f0/0
Router(config-if)#ipv6 address 2003::1/64
Router(config-if)#no shut

Now Routing

in routing use autonomous no. (10) which is similar in all router 
and router-id which is different in all router. 
in first router we use 1.1.1.1
in second router use 2.2.2.2.

NOW
Go to first router

First create group 

Router(config)#ipv6 unicast-routing
Router(config)#ipv6 router eigrp 10
Router(config-rtr)#eigrp router-id 1.1.1.1
Router(config-rtr)#no shut
Router(config-rtr)#exit

Now add port's of router in group

Router(config)#int s0/0/0
Router(config-if)#ipv6 eigrp 10
Router(config-if)#exit

Router(config)#int f0/0
Router(config-if)#ipv6 eigrp 10
Router(config-if)#exit

Now to second Router

Same as First router
            or

First create group 

Router(config)#ipv6 unicast-routing
Router(config)#ipv6 router eigrp 10
Router(config-rtr)#eigrp router-id 2.2.2.2
Router(config-rtr)#no shut
Router(config-rtr)#exit

Now add port's of router in group

Router(config)#int s0/0/0
Router(config-if)#ipv6 eigrp 10
Router(config-if)#exit

Router(config)#int f0/0
Router(config-if)#ipv6 eigrp 10
Router(config-if)#exit

Now checking

Send packet from one router to another router. or ping all ip

Comments

Post a Comment

Popular posts from this blog

Supernet

-
Supernet Supernet is used for to merge multiple route into single router. Supernet is create max.7 network Supernet is covered in into small size network Supernet create in 4 step’s 1. First convert all ip into binary 2. Now set the end operation end operation condition’s. operation are       a. all bit is one then output is one       b. all bit is zero then output is zero       c. if one bit is one and second is zero then output will zero 3. After set end operation now create new ip 4.Count common bit and create subnet mask For example                       172.16.111.0                       172.16.112.0                       172.16.113.0  1. Now convert it into binary.       10101100         00010000              01101111        00000000 10101100         00010000              01110000        00000000 10101100         00010000              01110001        00000000 2. Now set the end operation end operation condition’s and create new ip  10101100         00010000               01101111
Read more

How to connect two Laptops via mobile hotspot

-
If we want to transfer a file or a folder without any physical medium then we can use mobile hotspot as a mediatior. To connect two laptops we have to go through several steps. Steps:- first on the hotspot of mobile and connect to both laptops and connect to both laptops then open network and check devices if net is off then give manual ip in both laptop then check both laptops in network then share data from first laptop Steps:- First copy all the data in a folder --> go to folder properties --> click on share --> advance --> check mark on "share the folder" --> permission --> check mark on full control-->ok-->close Now go to another laptop-->network-->open another laptop-->and paste the data.
Read more

Router Password

-
Router Password There are three type of password set in Router. 1. Enable Password 2. Console Password 3. Telnet Password Enable Password  These is First mode of router. It is set for enable mode HOW TO SET go to router Router>enable Router#config t Router(config)#enable secret  123456      ------ password Router>enable Router#config t#exit TO check exit all terminal and re-enter in console terminal Router>enable Password ----------- this is shown after set password Console Password  These password is used for router excess in P.C. Router>enable Router#config t Router(config)#line console 0 Router(config-line)#password abc ----- password Router(config-line)#login To check  exit from all terminal and restart Password ---- before Router> terminal Telnet Password or Virtual teletype Password (VTY) It is use when you remote access to another router. Router>enable Router#config t Router(config)#line vty 0 4 Router(config-line)#password 123 ----- password Router(config-line
Read more