OSPF(Open Short Path First) Routing with IPV6
OSPF(Open Short Path First) Routing with IPV6
For ipv4 Routing
Diagram
Router 2811 and switch 2950T
Basic Configuration,clock rate and bandwidth
Go to First RouterRouter>en
Router#conf t
Router(config)#int s0/0/0
Router(config-if)#ipv6 address 2002::1/64
Router(config-if)#no shut
Router(config-if)#clock rate 64000
Router(config-if)#bandwidth 1000
Router(config-if)#exit
Router(config)#int f0/0
Router(config-if)#ipv6 address 2001::1/64
Router(config-if)#no shut
Go to second Router
Router>en
Router#conf t
Router(config)#int s0/0/0
Router(config-if)#ipv6 address 2002::2/64
Router(config-if)#no shut
Router(config-if)#bandwidth 1000
Router(config-if)#exit
Router(config)#int f0/0
Router(config-if)#ipv6 address 2003::1/64
Router(config-if)#no shut
Now Routing
1. in routing use Product ID (10) which is similar in all router
2. router-id which is different in all router.
in first router we use 1.1.1.1
in second router use 2.2.2.2
3. In ospf also use area no. area 0 is backbone of network.
NOW
Go to first router
First create group
Router(config)#ipv6 unicast-routing
Router(config)#ipv6 router osfp 10
Router(config-rtr)#router-id 1.1.1.1
Router(config-rtr)#exit
Now add port's of router in group
Router(config)#int s0/0/0
Router(config-if)#ipv6 ospf 10 area 0
Router(config-if)#exit
Router(config)#int f0/0
Router(config-if)#ipv6 ospf 10 area 0
Router(config-if)#exit
Router(config)#ipv6 router osfp 10
Router(config-rtr)#router-id 1.1.1.1
Router(config-rtr)#exit
Now add port's of router in group
Router(config)#int s0/0/0
Router(config-if)#ipv6 ospf 10 area 0
Router(config-if)#exit
Router(config)#int f0/0
Router(config-if)#ipv6 ospf 10 area 0
Router(config-if)#exit
Now go to second router
Same as router first
or
First create group
Router(config)#ipv6 unicast-routing
Router(config)#ipv6 router osfp 10
Router(config-rtr)#router-id 2.2.2.2
Router(config-rtr)#exit
Now add port's of router in group
Router(config)#ipv6 router osfp 10
Router(config-rtr)#router-id 2.2.2.2
Router(config-rtr)#exit
Now add port's of router in group
Router(config)#int s0/0/0
Router(config-if)#ipv6 ospf 10 area 0
Router(config-if)#exit
Router(config)#int f0/0
Router(config-if)#ipv6 ospf 10 area 0
Router(config-if)#exit
Router(config-if)#ipv6 ospf 10 area 0
Router(config-if)#exit
Router(config)#int f0/0
Router(config-if)#ipv6 ospf 10 area 0
Router(config-if)#exit
Now checking
Send packet from one router to another router. or ping all ip
------------------END----------------------
------------------END----------------------
Comments
Post a Comment