Routing By RIP-V2

Routing By RIP-V2 

   RIP-V2 (Routing information Protocol Version 2)

       1.   It is RIP second form

       2.   RIP-V2 is also Dynamic routing protocol

       3.   RIP-V2 is classless routing protocol

       4.   RIP-V2 is Max. Support is 15 network

Different Between RIP and RIPV2

   RIP support classful network only

   RIP-V2 Support both classful and classless network 

   Classful network does not use subnetting ip.

   Classless network is support Subnetting ip. It is also known as         CIDR (Classless interdomain Routing)

Now Configure By RIP-v2 Dynamic Routing

1. Diagram

First take router(2621-XM) and add port(WIC-2T) According to following  Diagram 

Go to first router in cli mode and type

          No

          Router>en

          Router#conf t

          Router(config)#int s0/0

          Router(config-if)#ip address 192.168.30.1 255.255.255.0

          Router(config-if)#no shut

          Router(config-if)#clock rate 64000

          Router(config-if)#exit

          Router(config)#int f0/0
   Router(config-if)#ip address 192.168.10.1 255.255.255.0
   Router(config-if)#no shut

          Router(config-if)#exit
        Router(config)#int f0/1
        Router(config-if)#ip address 172.16.1.1 255.255.255.0

        Router(config-if)#no shut

         Router(config-if)#exit

Go to second router in cli mode

          No

          Router>en

          Router#conf t

          Router(config)#int s0/0

          Router(config-if)#ip address 192.168.30.2 255.255.255.0

          Router(config-if)#no shut

          Router(config-if)#exit

          Router(config)#int s0/1

          Router(config-if)#ip address 192.168.40.1 255.255.255.0

          Router(config-if)#no shut

          Router(config-if)#clock rate 64000

          Router(config-if)#exit

          Router(config)#int f0/0

          Router(config-if)#ip address 192.168.20.1 255.255.255.0

          Router(config-if)#no shut

          Router(config-if)#exit
         Router(config)#int f0/1
         Router(config-if)#ip address 172.17.1.1 255.255.255.0

         Router(config-if)#no shut

         Router(config-if)#exit

Go to Third router in cli mode

          No

    Router>en

          Router#conf t

    Router(config)#int s0/0

          Router(config-if)#ip address 192.168.40.2 255.255.255.0

          Router(config-if)#no shut

          Router(config-if)#exit

          Router(config)#int f0/0

          Router(config-if)#ip address 192.168.50.1 255.255.255.0

          Router(config-if)#no shut

          Router(config-if)#exit
         Router(config)#int f0/1
         Router(config-if)#ip address 172.18.1.1 255.255.255.0

         Router(config-if)#no shut

         Router(config-if)#exit

Step 2 Routing  

In First Router

First check network in (Router# Show ip route)

Then type

Router#conf t

Router(config)#router rip
Router(config-router)#version 2

Router(config-router)#network 192.168.10.0

Router(config-router)#network 192.168.30.0

Router(config-router)#network 172.16.1.1

In Second router

Router# Show ip route

Router#conf t

Router(config)#router rip

Router(config-router)#version 2
Router(config-router)#network 192.168.20.0

Router(config-router)#network 192.168.30.0

Router(config-router)#network 192.168.40.0

Router(config-router)#network 172.17.1.1

In Thrid router

Router# Show ip route

Router#conf t

Router(config)#router rip
Router(config-router)#version 2

Router(config-router)#network 192.168.40.0

Router(config-router)#network 192.168.50.0

Router(config-router)#network 172.18.1.1

To check Send Packet's Between Networks or ping IP 
go to first router and ping last router according to the diagram.

                    -----------------------------------END--------------------------------